Printed Wiring Boards Services Unequal copper distribution between different Layers of PWB and Printed Circuit Boards leads to substantially higher curvature and twisting values.

... To help you quickly access the services we offer, the following is a guide to the preferred requirements for producing quality Printed Circuit Boards. | PRINTED WIRING BOARDS SERVICES | Can be supplied as artworks, penplots, photoplots or photoplot files, so long as the quality and registration of the images is of a standard that | PRINTED WIRING BOARDS SERVICES | will enable a good quality board to be produced. Another important criteria is the presence of orientation marks within the boundary of board. These marks | PRINTED WIRING BOARDS SERVICES | could be the board reference so long as it cannot be read from the other side. (This is for your protection to prevent the boards | PRINTED WIRING BOARDS SERVICES | made inside out). Images should comply with design rules that will result in a board that will meet performance and cost requirements. ARTWORKS Scale must | PRINTED WIRING BOARDS SERVICES | be given, tapes securely stuck to the backing sheet, track to pad & track to track joints complete and the backing sheet clean. PENPLOTS Scale | PRINTED WIRING BOARDS SERVICES | must be given and be at least 2:1. Plots must also offer sharp edge definition and traces dense enough for ...
[ Printed Wiring Boards Services ]


... production on to you. Data preparation and technical support is, of course, included. | SELECTED CAPABILITIES: | Archiving Process Data Drill- / Milling Program | PRINTED WIRING BOARDS SERVICES | Archiving Customer Data Production Data Conversion E-Test optional Design Check UL - Listing optional Design Adjustment Further Options | TECHNICAL SPECIFICATION: | Delivery: in Single | PRINTED WIRING BOARDS SERVICES | Board Format as well as in Panelized Board Arrays and Sub-Arrays with / without Fixing Tabs finished by Milling and Scoring to size. M| ILLING-COORDINATES | PRINTED WIRING BOARDS SERVICES | [-?-]: | One with Milled Outline. One MAA-Unit (MAA-U) is made up of 20 MAA´s Data-Base Format: Gerber, ODB++, DPF Type of the Base Material: | PRINTED WIRING BOARDS SERVICES | FR 4 Amount of Layers: 1, 2, 4, 6 Surface Protection: HAL Layer Build-Up: | ELECTRICAL TESTING: | Flying Probe or Adaptor Final Thickness of | PRINTED WIRING BOARDS SERVICES | PCB: 1,55 mm to 2,40 mm Junction in Line-Production: Yes Min. Track Width + Spacing: 150µ / 150µ Smallest pad: 0,80 mm Min PCB-Length / | PRINTED WIRING BOARDS SERVICES | With: 10 x 10 mm Min. finished Hole Size: 0,30 mm Min Milling Tool: 2,00 ...
[ Printed Wiring Boards Services ]


... PCBs. Residues, constricted conductors and subcorrosions can be discovered which would otherwise lead to PCB failure after a number of operational hours. An electrical | PRINTED WIRING BOARDS SERVICES | test is needed to check the actual functions of a PCB. It is an essential if inner layers need to be tested, as is the | PRINTED WIRING BOARDS SERVICES | case with multi-layers. In two position measure-ments all connections in the PCB are checked for stoppages and short circuits. All SMD pads and plated through | PRINTED WIRING BOARDS SERVICES | holes are checked. The electrical test can be conducted as a parallel or finger test. Parallel test: For the parallel test a control adaptor is | PRINTED WIRING BOARDS SERVICES | constructed, consisting, e.g. of several synthetic sheets positioned above each other and fitted with control pins. An adaptor programme must be written to reflect the | PRINTED WIRING BOARDS SERVICES | actual holes in each individual synthetic layer of the adaptor. The pin positions are identical to the control points enabling an overall PCB test within | PRINTED WIRING BOARDS SERVICES | seconds. The control adaptors are all the more expensive the higher the density ...
[ Printed Wiring Boards Services ]